Analysis of Priority Improvement in Draft Quality of Sizing Using Grey Theory in FMEA
DOI:
https://doi.org/10.22441/ijiem.v6i1.29858Kata Kunci:
FMEA, Grey theory, Draft quality, Sizing, Warp breakAbstrak
Draft quality is a crucial problem in the sizing section. There were 3889 warp yarn breaks for six months. The study aims to decrease quality draft defects by applying the grey theory in the traditional FMEA. After analyzing the flow process, 41 potential causes (PC) were found from 12 potential failure modes in 7 areas. There is no significant difference in the top 5 rankings of the RPN assessment on traditional FMEA and grey theory. However, there is a slight difference in ranking on 5 PC. The first priority (RPN= 48; GR=0.588) is in the beam shaft with the creel unaligned in the beam installation (pneumatic piston not parallel). The last priority (RPN= 4; GR=0.857) is a less oiling. This research can recommend an improvement sizing process based on the proposed repairs or maintenance list, using the Grey theory in the FMEA method to decrease the weaving industry defect rate.Unduhan
Referensi
Afdal, Z. A., & Linarti, U. (2023). Preventive Maintenance Analysis Using Monte Carlo Simulation and Failure Mode and Effect Analysis (FMEA). Jurnal Ilmiah Teknik Industri, 22(2), 251–262. https://doi.org/10.23917/jiti.v22i2.21900
Ahmed, T., & Uddin, S. (2023). Textile weaving dataset for machine learning to predict rejection and production of a weaving factory. Data in Brief, 47, 108995. https://doi.org/10.1016/j.dib.2023.108995
Al Masud, A., Hossain, M. A., & Biswas, S. (2021). Impact of human resource management practices on the performance of the textile employees in barishal region. Annals of the Romanian Society for Cell Biology, 5291–5304.
Ali, S. R., Al Masud, A., Hossain, Md. A., Islam, K. M. Z., & Shafiul Alam, S. M. (2024). Weaving a greener future: The impact of green human resources management and green supply chain management on sustainable performance in Bangladesh’s textile industry. Cleaner Logistics and Supply Chain, 10, 100143. https://doi.org/10.1016/j.clscn.2024.100143
Ayele, M., & Abay, A. G. (2023). Analyzing the Effect of Various Sizing Machine Settings on Abrasion Resistance and Size Pick-Up of Polyester/Cotton Blend Sized Yarn Using Box-Behnken Design. Journal of Natural Fibers, 20(1), 2165591. https://doi.org/10.1080/15440478.2023.2165591
Chang, C., Liu, P., & Wei, C. (2001). Failure mode and effects analysis using grey theory. Integrated Manufacturing Systems, 12(3), 211–216. https://doi.org/10.1108/09576060110391174
Devare, M. D., Turukmane, R. N., Gulhane, S. S., & Patil, M. L. C. (2016). International Journal on Textile Engineering and Processes ISSN 2395-3578 Vol. 2, Issue 4 October 2016. 2(4).
Ebeling, C. E. (2019). An introduction to reliability and maintainability engineering. Waveland Press.
Ervural, B., & Ayaz, H. I. (2023). A fully data-driven FMEA framework for risk assessment on manufacturing processes using a hybrid approach. Engineering Failure Analysis, 152, 107525. https://doi.org/10.1016/j.engfailanal.2023.107525
Fajriah, N., Mahfud, H., & Hayati. (2023). Analysis and Minimization of Waste in the Production Area of PT. XYZ with Lean Manufacturing Approach and System Simulation. 22(2), 229–233. https://doi.org/10.23917/jiti.v22i2.22464
Febianti, E., Ferdinant, P. F., Wahyuni, N., & Riyani, D. N. (2020). Usulan Penjadwalan Perawatan Mesin Menggunakan Metode Reliability Block Diagram. Performa: Media Ilmiah Teknik Industri, 19(1). https://doi.org/10.20961/performa.19.1.40983
G. Huang, L. Xiao, W. Pedrycz, G. Zhang, & L. Martinez. (2023). Failure Mode and Effect Analysis Using T-Spherical Fuzzy Maximizing Deviation and Combined Comparison Solution Methods. IEEE Transactions on Reliability, 72(2), 552–573. https://doi.org/10.1109/TR.2022.3194057
Gandhi, K. L. (2020). Yarn preparation for weaving: Sizing. In Woven Textiles (pp. 119–166). Elsevier. https://doi.org/10.1016/B978-0-08-102497-3.00004-0
Genene Abay, A., & Ayele, M. (2023). Multiple response optimization of sizing machine settings and sized yarn tensile properties using advanced method of experimental design. Journal of Engineered Fibers and Fabrics, 18, 15589250231179621. https://doi.org/10.1177/15589250231179621
Huang, J., Guo, W., Shi, H., & Liu, H.-C. (2023). A social network analysis-based model for failure mode and effect analysis under linguistic preference relation environment. Engineering Applications of Artificial Intelligence, 126, 107119. https://doi.org/10.1016/j.engappai.2023.107119
Jahangir, D., & Hossain, M. S. (2023). Analysis of the Effect of Sizing Add-on% and Sizing Process Parameters on the Average Warp Breakage Rate for 30Ne 100% Cotton Warp Yarn. Journal of Engineering Science, 13(2), 111–115. https://doi.org/10.3329/jes.v13i2.63731
Ju, Y., Zhao, Q., Luis, M., Liang, Y., Dong, J., Dong, P., & Giannakis, M. (2024). A novel framework for FMEA using evidential BWM and SMAA-MARCOS method. Expert Systems with Applications, 243, 122796. https://doi.org/10.1016/j.eswa.2023.122796
Li, F., Zhang, L., Dong, S., Xu, L., Zhang, H., & Chen, L. (2024). Risk assessment of bolt-gasket-flange connection (BGFC) failures at hydrogen transfer stations based on improved FMEA. International Journal of Hydrogen Energy, 50, 700–716. https://doi.org/10.1016/j.ijhydene.2023.06.191
Liu, H.-C., Chen, X.-Q., Duan, C.-Y., & Wang, Y.-M. (2019). Failure mode and effect analysis using multi-criteria decision making methods: A systematic literature review. Computers & Industrial Engineering, 135, 881–897. https://doi.org/10.1016/j.cie.2019.06.055
Ma, Q., Zhu, X., Pu, Q., Liu, J., Fu, G., & Zhang, R. (2024). A method based on q-rung orthopair fuzzy cognitive map and TOPSIS method for failure mode and effect analysis considering risk causal relationships. Engineering Failure Analysis, 158, 107970. https://doi.org/10.1016/j.engfailanal.2024.107970
Minguito, G., & Banluta, J. (2023). Risk management in humanitarian supply chain based on FMEA and grey relational analysis. Socio-Economic Planning Sciences, 87, 101551. https://doi.org/10.1016/j.seps.2023.101551
Moon, S. K., Oh, H. S., Venture, J. A., Kim, J. K., & Yoon, Y.-J. (2013). Service reliability improvement in manufacturing and operating systems. International Journal of Precision Engineering and Manufacturing, 14(8), 1401–1406. https://doi.org/10.1007/s12541-013-0189-5
Nabi, G. (2022). Devices and Procedures Regulation in Medical Practice: Is There a Need for More transparency? Scottish Medical Journal, 67(1), 1. Scopus. https://doi.org/10.1177/00369330221080789
Nasrallah, I., Sabbah, I., Haddad, C., Ismaiil, L., Kotaich, J., Salameh, P., … Bawab, W. (2023). Evaluating the academic scientific laboratories’ safety by applying failure mode and effect analysis (FMEA) at the public university in Lebanon. Heliyon, 9(12), e21145. https://doi.org/10.1016/j.heliyon.2023.e21145
Ni, R., Meng, J., Cheng, M., Ke, Q., Zhao, Y., Li, X., & Zhao, Y. (2023). Recent advances of proteins extracted from agricultural and livestock wastes in biodegradable textile sizing applications. Process Safety and Environmental Protection, 177, 699–710. https://doi.org/10.1016/j.psep.2023.07.053
Ouyang, L., Che, Y., Yan, L., & Park, C. (2022). Multiple perspectives on analyzing risk factors in FMEA. Computers in Industry, 141, 103712. https://doi.org/10.1016/j.compind.2022.103712
Palange, A., & Dhatrak, P. (2021). Lean manufacturing a vital tool to enhance productivity in manufacturing. Materials Today: Proceedings, 46, 729–736. https://doi.org/10.1016/j.matpr.2020.12.193
Park, J., Park, C., & Ahn, S. (2018). Assessment of structural risks using the fuzzy weighted Euclidean FMEA and block diagram analysis. The International Journal of Advanced Manufacturing Technology, 99(9–12), 2071–2080. https://doi.org/10.1007/s00170-018-1844-x
Pravitasari, F., Kusumadewi, A., & Barat, J. (2023). Mitigation of Insert Separator Damage in Open-End Machines Penanggulangan kerusakan insert separators pada mesin open end. 05(01). http://dx.doi.org/10.37577/sainteks.v%vi%i.459
Pujianto, H. (2021). Reduksi Limbah Benang Cath Cord Pinggiran Kain untuk Penghematan Bahan Baku Benang Cath Cord dan Biaya Produksi pada Mesin Tenun Rapier PT XYZ dengan Percobaan Produksi pada Laboratorium Pertenunan AK-Tekstil Solo. 29.
Pujianto, H., Yulianto, B., Bintang, H. S., & Pramesti, D. A. (2023). Optimum Splice Thickness Ratio Splicer of a Winding Machine to PE20KT Thread Splicing Quality. Sainteks: Jurnal Sains dan Teknik, 5(2), 228–235. https://doi.org/10.37577/sainteks.v5i2.605
Rahayu, A. (2016). Evaluasi Efektivitas Mesin Kiln dengan Penerapan Total Productive Maintenance pada Pabrik II/III PT Semen Padang. Jurnal Optimasi Sistem Industri, 13(1), 454. https://doi.org/10.25077/josi.v13.n1.p454-485.2014
Rajput, S. K., Gulhane, S. S., Turukmane, R. N., & Basak, S. (2018). Benchmarking the End Breakage Rate of Sized Beam for Improving Loom Efficiency. 4(2).
Rashedul Islam, K. Md. (2023, May 27). Demystifying Most 25 Yarn Winding Defects and Remedies/ Effective Solution for Seamless Production. Retrieved 19 August 2023, from Winding Defects and Remidies website: https://textiletrainer.com/yarn-winding-defects-and-remedies/#google_vignette
Rong, Y., Yu, L., Liu, Y., Simic, V., Pamucar, D., & Garg, H. (2024). A novel failure mode and effect analysis model based on extended interval-valued q-rung orthopair fuzzy approach for risk analysis. Engineering Applications of Artificial Intelligence, 136, 108892. https://doi.org/10.1016/j.engappai.2024.108892
Shaju, K., Babu, S., & Thomas, B. (2023). Analysing effectiveness of grey theory-based feature selection for meteorological estimation models. Engineering Applications of Artificial Intelligence, 123, 106243. https://doi.org/10.1016/j.engappai.2023.106243
Sharma, R. K., Kumar, D., & Kumar, P. (2005). Systematic failure mode effect analysis (FMEA) using fuzzy linguistic modelling. International Journal of Quality & Reliability Management, 22(9), 986–1004. https://doi.org/10.1108/02656710510625248
Turukmane, R., Gulhane, S., & Patil, R. (2019). Impact of process parameters on sizing machine performance-A review. Melliand International, 25, 182–183.
Wan, X., Cen, L., Yue, W., Xie, Y., Chen, X., & Gui, W. (2024). Failure mode and effect analysis with ORESTE method under large group probabilistic free double hierarchy hesitant linguistic environment. Advanced Engineering Informatics, 59, 102353. https://doi.org/10.1016/j.aei.2024.102353
Wang, H., Zhang, Y.-M., & Yang, Z. (2019). A risk evaluation method to prioritize failure modes based on failure data and a combination of fuzzy sets theory and grey theory. Engineering Applications of Artificial Intelligence, 82, 216–225. https://doi.org/10.1016/j.engappai.2019.03.023
Yu, Y., Yang, J., & Wu, S. (2023). A novel FMEA approach for submarine pipeline risk analysis based on IVIFRN and ExpTODIM-PROMETHEE-II. Applied Soft Computing, 136, 110065. https://doi.org/10.1016/j.asoc.2023.110065
Zhou, Q., & Thai, V. V. (2016). Fuzzy and grey theories in failure mode and effect analysis for tanker equipment failure prediction. Safety Science, 83, 74–79. https://doi.org/10.1016/j.ssci.2015.11.013
Unduhan
Diterbitkan
Cara Mengutip
Terbitan
Bagian
Lisensi
The copyright to this article is transferred to Universitas Mercu Buana (UMB) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UMB. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.
We declare that:
1. This paper has not been published in the same form elsewhere.
2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.
Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UMB. The copyright transfer covers the exclusive right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
2. Authors may reproduce or authorize others to reproduce the Work or derivative works for the authors personal use or for company use, provided that the source and the UMB copyright notice are indicated, the copies are not used in any way that implies UMB endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
3. Although authors are permitted to re-use all or portions of the Work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.
