SIMULASI TURBIN ANGIN DENGAN BEBERAPA TIPE AIRFOIL MENGGUNAKAN SOFTWARE QBLADE
DOI:
https://doi.org/10.22441/jtm.v11i2.10801Keywords:
Airfoil, Qblade, Turbin Angin, DayaAbstract
Indonesia adalah negara yang memiliki potensi sumber energi terbarukan yang cukup besar, salah satunya adalah sumber energi angin yang potensinya mencapai 100 MW. Namun, pemanfaatan sumber energi angin di Indonesia masih belum maksimal, yakni baru sekitar 1.6% atau sekitar 1.6 MW. Desain turbin angin dan pengukuran kecepatan angin rata-rata merupakan hal yang penting dalam pemanfaatan potensi energi angin. Oleh sebab itu, dibutuhkan pengetahuan perihal desain dan simulai dari beberapa parameter yang mempengaruhi pemanfaatan energi angin, seperti jenis airfoil , kecepatan angin, pitch angle turbin angin, dan parameter desain turbin angin. Dalam penelitian ini, akan dilakukan desain sekaligus simulasi turbin angin menggunakan software Qblade dengan beberapa tipe airfoil yang berbeda, untuk mengetahui tipe airfoil dengan bentuk geometrinya yang paling efisien dalam membangkitkan daya pada turbin angin.
Downloads
References
Adhi Prasetyo, Didik Notosudjono, Hasto Soebagja, 2019, STUDI POTENSI PENERAPAN DAN PENGEMBANGAN PEMBANGKIT LISTRIK TENAGA ANGIN DI INDONESIA, Bogor : Universitas Pakuan
America Society for Engineering Education, 2011, Coherent Aplication Threads : Wind Turbine, Boston University, Mechanical Engineering Department
Bili Darnanto Susilo, (2017), “Perancangan Bilah tipe taperless untuk horizontal axis wind turbine”, Jember, Universitas Jember
D. Marten, J. Wendler, G. Pechlivanoglou, C.N. Nayeri1 , C.O. Paschereit, (2013), “QBLADE: AN OPEN SOURCE TOOL FOR DESIGN AND SIMULATION OF HORIZONTAL AND VERTICAL AXIS WIND TURBINES”, Berlin Germany, International Journal of Emerging Technology and Advanced Engineering
Fajrur Rahman Hakim, Indra Herlambang Siregar, 2014, Karakteristik Turbin Angin Vertical Axis dengan Lima Blade Profil NACA 0018, Surabaya : Universitas Negeri Surabaya
Illa Rizianiza, Devi Setiorini, Alfian Djafar, Perancangan Prototipe Turbin Angin Sumbu Horizontal Tiga Sudu Studi Kasus Institut Teknologi Kalimantan, Kalimantan : Institut Teknologi Kalimantan
Kementerian ESDM RI, 21 September 2018
M. Ragheb, (2014), “Optimal Rotor Tip Speed Ratio”
Maidi Saputra, Herri Darsan, Al Munawir, 2 Oktober 2019, KECEPATAN ANGIN: MENGGUNAKAN MAWAR ANGIN SEBAGAI PREDIKTOR ; Universitas Teuku Umar - Meulaboh : Jurnal Mekanova
Mohamed Hatim Ouahabi, Mohamed Marouan Inchenial, Farid Benabdelouahad, 2017, Aerodynamic analysis of two dimensional models of turbulence for two different airfoils to determine their efficiency for wind turbine blade, Morocco : International Workshop on Complex Turbulent Flows
Mr. Shubham Raut , Mr. Shubham Shrivas , Mr. Rohan Sanas , Mr. Navjyot Sinnarkar , Prof. M. K.Chaudhary, 2017, Simulation of Micro Wind Turbine Blade in QBlade, India : Savitribai Phule Pune University
Panggih Raharjo, (2010), “Terminologi airfoil”
Raghel Yunginger, Nawir. N.Sune, 2015, ANALISIS ENERGI ANGIN SEBAGAI ENERGI ALTERNATIF PEMBANGKIT LISTRIK DI KOTA DI GORONTALO, Gorontalo : Universtias Negeri Gorontalo
Rahmad Samosir, Kimar Turnip, Melya Dianasari Sebayang, 2017, OPTIMASI DAYA OUTPUT KINCIR ANGIN POROS HORIZONTAL DENGAN MENGGUNAKAN TEROWONGAN KERUCUT, Jakarta : GLOBAL JOURNAL OF ADVANCED ENGINEERING TECHNOLOGIES AND SCIENCES 4
Soeripno Martosaputroa , Nila Murtia, 2014, Blowing the Wind Energy in Indonesia, Tangerang : Scientific Committee of Indonesia EBTKE Conex 2013
Downloads
Published
How to Cite
Issue
Section
License
The copyright to this article is transferred to Universitas Mercu Buana (UMB) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UMB. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.
We declare that:
1. This paper has not been published in the same form elsewhere.
2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.
Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UMB. The copyright transfer covers the exclusive right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
2. Authors may reproduce or authorize others to reproduce the Work or derivative works for the authors personal use or for company use, provided that the source and the UMB copyright notice are indicated, the copies are not used in any way that implies UMB endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
3. Although authors are permitted to re-use all or portions of the Work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.
This work is also licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
