MANUFACTURE AND TESTING OF VIBRATION TEST SCHEMES FOR PIPING SYSTEMS
DOI:
https://doi.org/10.22441/jtm.v13i2.25377Keywords:
Perpipaan, getaran, katup, tumpuanAbstract
Piping system is the distribution of fluids through pipes. This is often in everyday life, an example is the water pipe in every house that is used to fulfill desires and in the industrial field pipes are often used to distribute petroleum fluids as well as offshore and onshore. Supports have a very important role to overcome the loads that occur at points that experience excessive loads caused by the weight of pipes and other devices. In general, dynamic failures in pipe systems are caused by resonance from the vibrations of the pipe stretch. Therefore, this research is intended to determine the effect of valve opening variation and pedestal distance variation on vibration in the pipe system so that it can be used for consideration in designing a piping system. This research uses an experimental approach starting with the preparation of a vibration test scheme and then testing using a vibration meter. The test data was processed and statistically analyzed so that it was found that at 100% valve opening, the largest value is at a pedestal distance of 180 cm with a flow rate of 2.8 m/s2 and the largest 50% valve opening is at the same pedestal distance of 180 cm with a flow rate of 2.3 m/s2. The farther the pedestal distance, the greater the vibration and deflection and the greater the flow discharge produced, the higher the vibration producedDownloads
References
. Nurnawaty and Sumardi., ”Analisis Perubahan Tinggi Tekanan Akibat Sudut Belokan 900 Dan 450 Dengan Menggunakan Fluid Friction Apparatus,” J. Teknik Hidro., Vol. 13 Nomor 1, Februari 2020.
. Walker and Rocky, “Fluid Power Handbook & Directory,” Nevada, 2007.
. A. Geraldine Andreas, et all., “Analisis Tekuk Kritis Pada Pipa Akibat Tekanan Internal,” Jurnal Teknik Perkapalan, Vol. 4, No.3 Juli
. Irsan Faisal Pasaribu and Zulfikar., “Rancang Bangun Sistem Kontrol Buka Tutup Valve Pada Proses Pemanasan Air Jaket,” J. Teknik Elektro, Vol. 1, No. 1, Juli 2018.
. Hidayat., “Tumpuan & Reaksi Gaya”, 2020.
. Hidayat Royan and Galuh Renggani Wilis., “Analisis Getaran Pada Kompresor Mesin Pendingin Dengan Variasi Putaran (Rpm),” Vol. 15 No. 2 Oktober 2017.
. Berry, J.E., “Predictive Maintenance and Vibration Signature Analysis 1,” 1997.
. Sufiyanto, Hariyanto R, Darto., “Simulasi Model Karakteristik Self Excited Vibrations Dalam Aliran Fluida Dengan Ansys.” Prosiding Seminar Nasional Aplikasi Sains & amp; Teknologi (SNAST): B143-150. 2014.
. Thomson W.T. and Dahleh M.D., “Theory of Vibration with Applications” th Ed. Prentice Hall, 1997.
. Andrianyah dan Abidin Z., “Analisis Kesalahan Perhitungan Nilai RMS Sinyal Sinusoidal Kontinu tanpa dan dengan Fungsi Jendela” e Nasional Tahunan Teknik Mesin XI, Yogyakarta, 2012.
. Sedlacek, M. and Novotny, M., “Measurement of RMS Values of Non-Coherently Sampled Signals” Czech Technical University, Faculty of Electrical Engineering, Department of Measurement, Prague, 2004.
. Schmitz, Tony L., and K. Scott Smith. "Mechanical vibrations." Modeling and measurement, 2012
Downloads
Additional Files
Published
How to Cite
Issue
Section
License
The copyright to this article is transferred to Universitas Mercu Buana (UMB) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UMB. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.
We declare that:
1. This paper has not been published in the same form elsewhere.
2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.
Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UMB. The copyright transfer covers the exclusive right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
2. Authors may reproduce or authorize others to reproduce the Work or derivative works for the authors personal use or for company use, provided that the source and the UMB copyright notice are indicated, the copies are not used in any way that implies UMB endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
3. Although authors are permitted to re-use all or portions of the Work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.
This work is also licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
