Determination of standard time with the stopwatch time study method at PT BI
DOI:
https://doi.org/10.22441/oe.2025.v17.i2.145Keywords:
productivity, standard time, stopwatch, time studyAbstract
In the manufacturing industry, the effectiveness of the work process is one of the key factors to increase the efficiency and competitiveness of the company. One of the main challenges is the accurate determination of standard working times, especially in processes involving manual inspections. Without a clear standard time standard, setting work targets is often not optimal, which can result in uneven workload, decreased productivity, and worker fatigue. PT BI is an automotive component manufacturing company that uses cold forging technology. One of the important processes in this company is visual inspection to guarantee product quality. However, the company does not yet have a standard time standard in the visual inspection process, so the daily target is determined based on the cycle time, which is less effective. This study aims to analyze the effectiveness of operators in using standard time in achieving targets. The study used the stopwatch time study method to measure the work cycle time in visual inspection operators. Data was collected through observations and interviews with operators as well as analysis using Minitab software. The results of the study show that the application of standard time is able to increase the effectiveness of operators in achieving daily targets. In addition, precise determination of standard timing provides companies with advantages with better process efficiency and reduced operator fatigue levels. In conclusion, the application of standard time can be the optimal solution to increase company productivity while maintaining worker welfare.Downloads
References
Bon, A. T., & Samsudin, S. N. A. (2018). Productivity improvement in assembly line by reduction cycle time using time study at automotive manufacturer. Proc. Int. Conf. Ind. Eng. Oper. Manag, 2018, 284–291.
Daryanto, D. (2021). Manajemen Produksi. Yrama Widya.
Krisnaningsih, E., Dwiyatno, S., & Sasongko, R. (2020). Usulan Penentuan Waktu Baku Pada Operator Packing Folding Kain Tetoron Rayon Dengan Metode Stopwatch. Jurnal Intent: Jurnal Industri Dan Teknologi Terpadu, 3(2), 67–81.
Lestari, E., Kristiyana, N., & Wahyuningsih, D. W. (2022). Pengaruh Pelatihan Kerja, Lingkungan Kerja, Dan Kompensasi Terhadap Tingkat Produktivitas Kerja Karyawan Studi Kasus Pada Ud. Karya Sejatera Desa Campursari Kecamatan Sambit Kabupaten Ponorogo. Bussman Journal: Indonesian Journal of Business and Management, 2(3), 604–619.
Marasabessy, U. R., Astrides, E., Ahistasari, A., Wahyudien, M. A. N., & Rachmadhani, M. M. (2023). Analysis of Work Measurement Using the Stopwatch Time Study Method at PTEA. Journal of Industrial System Engineering and Management, 2(1), 23–31.
Mayselah, N. (2023). Optimalisasi Produktivitas dengan Metode Time and Motion Study di PT. XYZ. Journal of Research on Industrial and System Engineering, 1(1), 1–12.
Montororing, Y. D. R. (2018). Usulan Penentuan Waktu Baku Proses Racking Produk Amplimesh Dengan Metode Jam Henti Pada Departemen Powder Coating. Jurnal Teknik: Universitas Muhammadiyah Tangerang, 7(2), 53–63.
Nurunni’mah, Z. F. (2019). Analisis Pengukuran Kerja Dalam Menentukan Waktu Standar Dengan Metode Studi Waktu Guna Meningkatkan Produktifitas Kerja Pada Shuttlecock PT. Garuda Budiono Putra. Fakultas Ekonomi Dan Bisnis, Universitas Pancasakti, Tegal.
Pradana, A. Y., & Pulansari, F. (2021). Analisis pengukuran waktu kerja dengan stopwatch time study untuk meningkatkan target produksi di PT. XYZ. JUMINTEN, 2(1), 13–24.
Prayuda, S. (2020). Analisis Pengukuran Kerja Dalam Menentukan Waktu Baku Untuk Meningkatkan Produktivitas Kerja Pada Produksi Kerudung Menggunakan Metode Time Study Pada Ukm Lisna Collection Di Tasikmalaya. Jurnal Mahasiswa Industri Galuh, 1(1), 120–126.
Purbasari, A., Sumarya, E., & Mardhiyah, R. (2023). Penerapan Metode Studi Waktu Dan Gerak Pada Proses Packing Di Pt. Abc. Sigma Teknika, 6(2), 290–299.
Rahma, M., & Pratama, A. J. (2019). Pengukuran Waktu Baku Stasiun Kerja Perakitan Komponen Pesawat Garuda Indonesia Temperature Control Valve (TCV) Menggunakan Metode Jam Henti Pada PT. GMF Aeroasia. Seminar Nasional IENACO-2019, 16–23.
Sutaarga, O., & Setiawan, A. (2021). Penentuan waktu baku dalam pengecekan bonding sampel sepatu pada PT. Ching Luh Indonesia. Journal Industrial Manufacturing, 6(1), 18–26.
Wahid, A., & Chumaedi, A. (2020). Penentuan Waktu Baku dengan Metode Stopwatch Time Study Proses Produksi Manifold (UD. Jaya Motor Pasuruan). JKIE (Journal Knowledge Industrial Engineering), 7(2), 54–60.
Yudisha, N. (2021). Perhitungan waktu baku menggunakan metode Jam Henti pada proses Bottling. Jurnal Vorteks, 2(2), 85–90.
Downloads
Published
How to Cite
Issue
Section
License
The copyright to this article is transferred to Universitas Mercu Buana (UMB) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UMB. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.
We declare that:
1. This paper has not been published in the same form elsewhere.
2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.
Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UMB. The copyright transfer covers the exclusive right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
2. Authors may reproduce or authorize others to reproduce the Work or derivative works for the authors personal use or for company use, provided that the source and the UMB copyright notice are indicated, the copies are not used in any way that implies UMB endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
3. Although authors are permitted to re-use all or portions of the Work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.
