Optimization of Basket Oven Oil Seal Design For Quality, Productivity and Material Handling
DOI:
https://doi.org/10.22441/ijiem.v4i3.20303Keywords:
Basket oven, Oil seal, and OptimizationAbstract
In the oil seal production process, one of them is the post-cure oven process as a heat treatment to engineer the rubber material so that it has resistance to friction and has high heat resistance. The post-cure oven process itself uses equipment in the form of an oven basket made of heat-resistant steel material to place the oil seal. However, the Basket oven itself has a maximum limit for placing the oil seal in the oven, so calculations are needed to find the optimization value to find out the maximum value obtained so as to increase work productivity. From the problems found, the existing oven baskets were unable to accommodate 1,442 pcs/lot of products, but were only able to accommodate 1,344 pcs of products. so it is necessary to design a new basket oven to get the optimal value so that the basket oven can accommodate as many as 1,442 pcs/lot of products. From the research results it is known that to save material the most optimum cutting value is if the value of x = 8.5. Meanwhile, to get the maximum volume value, it is cut with a value of x = 11. By using the new oven basket, the product volume that can be accommodated is 1,568 pcs when compared to the use of the old basket which was previously able to accommodate 1,344 pcs of product. The use of a new basket oven can increase basket volume by 16.7%.Downloads
References
Ats-Tsauri, M. I., Arrasyid, A., & Wiyatno, T. N. (2022). Optimisasi Non Linear Programming Multivariat pada Perencanaan Produksi Industri Manufaktur Baja Lapis Seng (BjLS). Jurnal Teknik Industri, 3(1), 16–25. https://doi.org/10.37366/jutin0301.1625
Bamidele, A. M., Oke, S. A., Rajan, J., Sawyerr, B. A., Fasina, E., Adedeji, K. A., & Oyetunji, E. O. (2023). Optimization of Friction Stir Welding Parameters of AA5052-H32 Aluminium Alloy using Taguchi and Taguchi-Pareto Methods. IJIEM - Indonesian Journal of Industrial Engineering and Management, 4(1), 61. https://doi.org/10.22441/ijiem.v4i1.18403
Cahyono, A., Prihono, P., & Nurcahyanie, Y. D. (2023). Optimization Through Linear Programming Method Simplex in Umkm Dongkal Awug Kang Cake in Bogor Regency. Jurnal Scientia, 12(02), 982–989. http://infor.seaninstitute.org/index.php/pendidikan/article/view/1324/1068
Finšgar, M., & Rajh, B. (2023). A Factorial
Design and Simplex Optimization of a Bismuth Film Glassy Carbon Electrode for Cd(II) and Pb(II) Determination. Chemosensors, 11(2), 22–29. https://doi.org/10.3390/chemosensors11020129
Harahap, L. H., Nasution, M. K. M., & Sawaluddin, S. (2023). A Mathematical Model of Diet Menu Problem Based on Boolean Linear Programming Approach. Sinkron, 8(3), 1453–1460. https://doi.org/10.33395/sinkron.v8i3.12592
Imanuela Mustamu, L., & Sibaroni, Y. (2023). Fuel Increase Sentiment Analysis Using Support Vector Machine With Particle Swarm Optimization and Genetic Algorithm As Feature Selection. Jurnal Teknik Informatika (Jutif), 4(3), 521–528. https://doi.org/10.52436/1.jutif.2023.4.3.881
Liang, C., Chen, C., Wang, W., Ma, X., Li, Y., & Jiang, T. (2022). Line Loss Interval Algorithm for Distribution Network with DG Based on Linear Optimization under Abnormal or Missing Measurement Data. Energies, 15(11). https://doi.org/10.3390/en15114158
Martins, S. A., & Oke, S. A. (2021). Multi-Response Optimization of Safety Conformity using Taguchi Scheme in a Bottling Process Plant. IJIEM - Indonesian Journal of Industrial Engineering and Management, 2(2), 94. https://doi.org/10.22441/ijiem.v2i2.10947
Ozule, C. P., Oke, S. A., & Nwankiti, U. S. (2022). Optimizing the Process Parameters for Eco-Friendly Minimum Quantity Lubrication-Turning of AISI 4340 Alloy with Nano-Lubricants Using a Grey Wolf Optimization Approach. IJIEM - Indonesian Journal of Industrial Engineering and Management, 3(3), 210. https://doi.org/10.22441/ijiem.v3i3.15519
Paduloh, P., & Mayana, T. (2023). Optimization of Delivery Cost on Reverse Logistic for Product Claim in the Two-Wheel Vehicle Industry. Jurnal Ilmiah Teknik Industri, 22(1), 33–39. https://doi.org/10.23917/jiti.v22i1.21469
Pratama, A. A. (2023). COMMODITIES USING THE SIMPLEX METHOD ( CASE STUDY OF COMPANY. May, 34–42.
Sarjono, J. S. (2021). Meminimasi Waste Pada Proses Pembuatan Oil Seal Dengan Pendekatan Lean Manufacturing (Studi Kasus Proses Produksi Oil Seal Line Sim Di Pt. Nok Indonesia). KOCENIN SERIAL KONFERENSI, Webinar Nasiional PAKAR KE 4, 1(1), 1–6.
Sultana, U., Khairuddin, A., Mokhtar, A. S., Qazi, S. H., & Sultana, B. (2017). An optimization approach for minimizing energy losses of distribution systems based on distributed generation placement. Jurnal Teknologi, 79(4), 87–96. https://doi.org/10.11113/jt.v79.5574
Swilam, A., Tahwia, A. M., & Youssf, O. (2022). Effect of Rubber Heat Treatment on Rubberized-Concrete Mechanical Performance. Journal of Composites Science, 6(10). https://doi.org/10.3390/jcs6100290
Tata, P., Relayout, L., Dan, K., Di, L., & Xyz, P. T. (2023). 16 https://publikasi.kocenin.com/index.php/teksi. 16–23.
Downloads
Published
How to Cite
Issue
Section
License
The copyright to this article is transferred to Universitas Mercu Buana (UMB) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UMB. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.
We declare that:
1. This paper has not been published in the same form elsewhere.
2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.
Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UMB. The copyright transfer covers the exclusive right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
2. Authors may reproduce or authorize others to reproduce the Work or derivative works for the authors personal use or for company use, provided that the source and the UMB copyright notice are indicated, the copies are not used in any way that implies UMB endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
3. Although authors are permitted to re-use all or portions of the Work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.
