Quality Control of Janggelan Products Using Statistical Quality Control (SQC) and Failure Mode Effect Analysis (FMEA) Methods in UD. Rizqi Agung
DOI:
https://doi.org/10.22441/ijiem.v5i2.22738Keywords:
Defect, FMEA, SQCAbstract
UD. Rizqi Agung is one of the SMEs in Ngrayun, Ponorogo. This SMEs is one of the medium-sized SMEs that produces packaged drinks. The packaged drinks produced are drinks made from janggelan juice. UD. Rizqi Agung has a production process that is still semi-manual so that there are still products that still have defects in these products. The methods used are Statistical Quality Control (SQC) and Failure Mode and Effect Analysis (FMEA). SQC tools are check sheet, stratification, histogram, paretto diagram, scatter diagram, control chart, and cause and effect diagram. While FMEA is used for improvement of the results of the cause and effect diagram. Based on the results of research on Sari Janggelan products, the most dominant defect is obtained, namely Cup Dent defects (4.06%), followed by Leak defects (2.84%), Dented Cardboard defects (1.30%), and Label not Symetric defects (1.22%). Proposed improvements with FMEA obtained risks that have the highest priority level to make improvements to minimize the possibility of errors. The highest RPN values is 320 and 288 of the type of cup dent defect with proposed improvement recommendations, namely changing cup vendors to match the quality requested by SMEs and monitoring employee performance.Downloads
References
Andespa, I. (2020). Analisis Pengendalian Mutu Dengan Menggunakan Statistical Quality Control (SQC) Pada PT. Pratama Abadi Industri (JX) Sukabumi. E-Jurnal Ekonomi dan Bisnis Universitas Udayana. Vol. 19, No. 2. pp 129-160. DOI:10.24843/eeb.2020.v09.i02.p02; Corpus ID: 219128334
Andriyanta, Galang., Aspiranti, T. dan Adwiyah, R. (2020). Analisis Pengendalian Kualitas dengan Menggunakan Metode Statistical Quality Control (SQC) untuk Meminimumkan Produk Gagal Pada Sari Good Bakery. Prosiding Manajemen, Vol. 6, No. 2.
Arif, M. (2016). Bahan Ajar Teknik Industri Edisi 1. Deepublish. Yogyakarta.
Dermawan, M. Arief. (2018). Penerapan Statistical Quality Control (SQC) untuk Megidentifikasi Complain Customer pada PT. Aerofood ACS Cabang Kualanamu. Universitas Sumatera Utara.
Hairiyah, N., Raden R. A., & Eva L. (2019). Analisis Statistical Quality Control (SQC) pada Produksi Roti di Aremania Bakery. Industria : Jurnal Teknologi dan Manajemen Agroindustri. Vol. 8, No. 1. https://doi.org/10.21776/ub.industria.2019.008.01.5
Haryanto, Irwandhani I. S. (2019). Penerapan Metode SQC (Statistical Quality Control) Untuk Mengetahui Kecacatan Produk Shuttlecock Pada Ud. Ardiel Shuttlecock. Jurnal Teknologi Industri Dan Menajemen Vol. 1 No.1.
Hutabarat, J. (2017). Pengantar Teknik Industri. Malang. Media Nusa Creative.
ILO. (2013). Produksi Bersih Produksi Bersih (Issue September). Jakarta: ILO.
Jannah, M., & Siswanti, D. (2017). Analisa Penerapan Lean Manufacturing Untuk Mereduksi Overproduction Waste Menggunakan Value Stream Mapping dan Fishbone Diagram. Jurnal Teknik. Vol. 6, No.1, pp. 1-9. DOI: https://doi.org/10.0001/77
Kuswardani, I., Ni Made S. Y. P., & Heni H. U. (2020). Analisis Pengendalian Kualitas Produk Telur di Persada Farm Dusun Argopeni Desa Sudimoro Kecamatan Srumbung Kabupaten Malang. Jurnal Dinamika Sosial Ekonomi. Vol. 21, No. 2. pp 105-121.
Manik, A. (2020). Usulan Perbaikan Kualitas Meggunakan Statistical Quality Control (SQC) dan Fuzzy Failure Mode and Effect Analysis (FMEA) untuk Meningkatkan Kualitas Produk Seng di PT. Intan Nasional Iron Industri. Skripsi. Jurusan Teknik Industri. Fakultas Teknik. Universitas Sumatera Utara. Medan.
Marimin, M.Sc., Prof., Dr., Ir (2004). Teknik dan Aplikasi Pengambil Keputusan Kriteria Majemuk. Jakarta : PT.Gramedia Widiasarana Indonesia.
Montgomery, D. C. (2013). Introduction to Statistical Quality Control 7th edition. John Wiley and Sons, Inc.
Nasution, M., N. (2001). Manajemen Mutu Terpadu (Total Quality Management). Jakarta : Ghalia Indonesia.
Novianti, Fenny. (2023). Quality Control of Edamame Products Using Statistical Quality Control (SQC) and Failure Mode Effect Analysis (FMEA) Methods in PT.XYZ. IJIEM. Vol. 4. No. 2. pp 221-230. https://dx.doi.org/10.22441/ijiem.v4i2.20550
Odi, A., Zaman, A. N., Nasution, S. R., & Sundana, S. (2019). Analisis Pengurangan Waste Pada Proses Perawatan Kereta. Jurnal ASIIMETRIK. Vol. 1, No. 1, pp. 34-42.
Purnama, Nursya'bani (2006). Manajemen Kualitas, Perspektif Global. Yogyakarta: Penerbit Ekonisia Fakultas Ekonomi UII Yogyakarta
Rachman, Taufiqur. (2012). Statistic Quality Control (SQC). Jakarta : Universitas Esa Unggul.
Rosyidi, M. R. (2021). Buku Ajar Pengendalian dan Penjaminan Mutu. Malang. Ahlimedia Press.
Saka, A. J., Izekor, J. A., Akeyede, I., Adeleke, M. O., & Adeleke, B. L. (2019). Dual Statistical Quality Control Charts with Table of Quality Determinant in Manufacturing Industries. International Journal of Information Processing and Communication (IJIPC). Vol 7, No. 1. pp 242-252.
Sari, Rianita Puspa. (2018). Analisis Tingkat Kecacatan Produk Lever Assy Parking Brake Menggunakan Metode Statistical Quality Control (SQC). JIEMS Vol. 11, No. 2, 77-83, 2018. DOI: https://dx.doi.org/10.30813/jiems.v11i2.1184
Walujo, D. A., Titiek K., & Yitno U. (2020). Pengendalian Kualitas. Surabaya. Scopindo Media Pustaka.
Downloads
Published
How to Cite
Issue
Section
License
The copyright to this article is transferred to Universitas Mercu Buana (UMB) if and when the article is accepted for publication. The undersigned hereby transfers any and all rights in and to the paper including without limitation all copyrights to UMB. The undersigned hereby represents and warrants that the paper is original and that he/she is the author of the paper, except for material that is clearly identified as to its original source, with permission notices from the copyright owners where required. The undersigned represents that he/she has the power and authority to make and execute this assignment.
We declare that:
1. This paper has not been published in the same form elsewhere.
2. It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.
3. A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.
Furthermore, I/We hereby transfer the unlimited rights of publication of the above mentioned paper in whole to UMB. The copyright transfer covers the exclusive right to reproduce and distribute the article, including reprints, translations, photographic reproductions, microform, electronic form (offline, online) or any other reproductions of similar nature.
The corresponding author signs for and accepts responsibility for releasing this material on behalf of any and all co-authors. This agreement is to be signed by at least one of the authors who have obtained the assent of the co-author(s) where applicable. After submission of this agreement signed by the corresponding author, changes of authorship or in the order of the authors listed will not be accepted.
Retained Rights/Terms and Conditions
1. Authors retain all proprietary rights in any process, procedure, or article of manufacture described in the Work.
2. Authors may reproduce or authorize others to reproduce the Work or derivative works for the authors personal use or for company use, provided that the source and the UMB copyright notice are indicated, the copies are not used in any way that implies UMB endorsement of a product or service of any employer, and the copies themselves are not offered for sale.
3. Although authors are permitted to re-use all or portions of the Work in other works, this does not include granting third-party requests for reprinting, republishing, or other types of re-use.
